Below are output numbers for different currents for the various brightness bins of more current LED models (see [[Old Cree LEDs]] for past models). There is more information available with the '''[http://pct.cree.com/ Cree Product Characterization Tool]''', an online calculator that allows you to look up output based on more factors. The numbers on this page, like those given by the PCT, are based on charts in the LED datasheets.
Below are output numbers for different currents for the various brightness bins of more current LED models (see [[Old Cree LEDs]] for past models). There is more information available with the '''[http://pct.cree.com/ Cree Product Characterization Tool]''', an online calculator that allows you to look up output based on more factors. The numbers on this page, like those given by the PCT, are based on charts in the LED datasheets.
==MC-E==
An older 4-die LED available with four of the same color dies or the MC-E Color with four different color dies (white, red, green, blue). The maximum current is 700mA with a Vf of 3.4V, though this varies from one color to another. Bins run from G (240 lumens) to M (430 lumens) at 350 mA. The white quadrant of the MC-E Color is available in cool white (A5) or neutral white (A4).
The MC-E was widely used in high-power flashlights like the EagleTac M2SC4, Fenix TK40, iTP A6 Polestar, and JETBeam M1X with advertised output of up to 700 lumens. The color version is in the Quark RGB (with neutral white or cool white available) but although the LED allows mixing of colors, the Quark RGB is switched to one color at a time.
[[File:Creexb-d.jpg|thumb|Cree XB-D is similar to the XT-E but smaller.]]Very compact LED (the die is mounted on a chip 2.45 mm square opposed to 3.45 mm square for XP series) introduced in February 2012, promising lower cost. Should provide similar brightness to XP-E LEDs. First available units were warm white with Q2 brightness bin (at 350mA). This LED is used in some budget Ozark Trail 3xAAA lights at Walmart. The XB-D is binned at an operating temperature of 85° C instead of 25°, so in order to directly compare its output to other LEDs that are typically binned at 25 degrees, the output numbers in the table below have been increased by 14% from what is shown in the datasheet (see [[XB-D output]] for the 85° numbers). Can be driven up to 1000mA. [http://www.cree.com/products/pdf/XLampXB-D.pdf Datasheet], [http://www.cree.com/news-and-events/cree-news/press-releases/2012/january/120111-xbd press release].
[[File:Cree-xml.jpg|thumb|Cree XM-L LED with 6 yellow strips and 3 bonding wires]]Widely used in high power flashlights, this larger die LED was first available in November 2011, offering efficacy of 160 lumens per watt at 350mA. Output is as high as 340 lumens at 700mA (bin U3, which is still rare) therefore it is more efficient and puts out more light at any current than earlier single-die Cree LEDs. However the biggest improvement to overall output is the XM-L can be driven to 3000mA for 1100 lumens of output. Because the XM-L is binned at 700mA, the bin numbers do not correlate exactly to those of the smaller die LEDs which are binned at 350mA. The LED die is 2mm x 2mm on a 5mm x 5mm substrate with 6 yellow strips and 3 bonding wires as opposed to the XP-G with 4 strips and 2 bonding wires and the XP-E with 3 strips and 2 bonding wires. The first production lights to feature the XM-L were versions of the [[ThruNite]] Catapult V2 (first to ship), [[EagleTac]] M3C4, a [[4Sevens]] Quark MiNi, and the [[JETBeam]] M1xm, introduced in December 2010, but budget retailer KaiDomain had LEDs and [[P60]] drop-ins as well as P60 lights around the same time. Neutral and warm tints began shipping in March 2011. [http://www.cree.com/news-and-events/cree-news/press-releases/2010/november/101110-xml Press release] [http://www.cree.com/products/pdf/XLampXM-L.pdf Cree XM-L datasheet]
[[File:Cree-xpc.jpg|thumb|Cree XP-C LED has a smaller die than the XP-E]]A lower current version of the XP-E with a smaller die. Maximum current 500mA and Vf of 3.5V. Bins up to Q4 (100 lumens) in cool white, Q2 in neutral white (84.7 lumens) and P3 in warm white (73.9 lumens). Looks like the XP-E, but the die has 2 yellow strips and 1 bonding wire instead of 3 strips and 2 bonding wires. The XP-C is used in the Streamlight Microstream and some Mini Maglites.
Introduced in Fall of 2008, the XP-E shrunk the XR-E by 80% (though it uses the same die), now 3.45 mm square. It is available, in white (cool, neutral, and warm), blue, green, amber, red, and red-orange. For cool white, bins are Q3, Q4, Q5, R2 and R3 with output from 93.9 to 122 lumens. Neutral white bins are from P4 to Q4 (100 lumens min) and warm white bins range from P2 to Q2 (87.4 lumens min).
This LED is used in the [[NiteCore]] Defender Infinity, early Quarks (R2, neutral whites used a Q3), the iTP A series EOS and S series lights, EagleTac P100 and T100 series.
The XP-E has 3 strips on the die as opposed to 2 on the XP-C and 4 on the XP-G.
Same size package as the XP-E, but with a larger die. Therefore the resulting beam has a little more flood. It is available in varying output bins from R2 to S3 (S2 and S3 are rare and not always the best tints). Maximum current is 1500mA and Vf of 3.3V with efficacy of 141 lumens per watt. [http://www.cree.com/products/pdf/XLampXP-G.pdf Cree XP-G datasheet], [http://www.cree.com/news-and-events/cree-news/press-releases/2009/september/090930-xp-g-led press release].
The XP-G R5 began widespread use in 2010 after being adopted early by 4Sevens and EagleTac. The limited edition titanium Quarks were among the first to use the XP-G, with an R4 bin. S2 bins became available in November 2010 but only in Quark and iTP special edition lights. Special edition matte-finish titanium Quark Mini and Turbo models were the first to feature S3 bins, shipping in December 2010.
Same size as XR-E (7mm x 9mm) but is designed for less current (500mA max). The die itself is smaller than the XR-E (same as the one in the XP-C). The maximum bin is Q2 with 87.4 lumens for cool white. It is available in white (cool, neutral, and warm) as well as royal blue, blue, green, amber, red-orange, and red. Vf is 3.5 volts at 350mA. Identifiable by the metal ring around the dome and a LED die with only two yellow strips and one bonding wire.
The XR-C is used in retail lights made by Coleman, River Rock, and Energizer.
==XR-E==
[[File:Cree_xre.jpg|thumb|Cree XR-E LED easily identified by the metal ring around the LED]]Introduced in the Fall of 2006 the XR-E was widely used in a number of different flashlights, with cool white, neutral white, and warm white colors available in addition to blue, royal blue, and green. Common bin numbers are P4, Q2, Q3, Q4, Q5, and R2 with increasing output from 80 lumens to 122 lumens at 350 mA and a Vf of 3.3V, but with much greater output available with higher currents. The size is 7 mm x 9 mm and you will often see this referred to as a 7090 XR-E. The die itself was available as the EZ1000 at first and then the smaller EZ900. Because the EZ900 can have the same overall output as the larger EZ1000 but in a smaller form, it should provide 23% greater intensity and throw (the EZ1000 is 1 mm square and the EZ900 is 0.9 mm square).
This LED was very widely used, featured in flashlights by [[Fenix]], [[JETBeam]], [[NiteCore]] D10, and [[EagleTac]] P20 and T20 series, and is still available in some [[budget lights]]. The neutral white version was used in Nitecore EZ series. It is easily recognized by the metal ring around the die with 3 yellow strips and 2 bonding wires.<br clear="all">
==XT-E==
[[File:Cree-xte.jpg|thumb|Cree XT-E LED]]Introduced in February 2012, the XT-E has the same size chip as the XP series but seems to have a wider viewing angle for more flood and less throw. Can be driven up to 1.5A and available in bins up to R5 (at 350mA). This LED is binned at an operating temperature of 85° C instead of 25°, so in order to directly compare its output to other LEDs that are typically binned at 25 degrees, the numbers in the table below have been increased by 14% (see [[XT-E output]] for the 85° numbers). Cree introduced the XT-E as a low-cost, high efficiency LED capable of 148 lumens per watt at 350mA, offering higher lumens per dollar. The LED is not a flat square, but has an X shaped hill on the surface. The beam is like a small XM-L with a large hotspot and some varying tint across the beam. [[EagleTac]] announced that the XT-E would be an option in its D25 clicky series in April 2012, but XT-E lights were never actually released, supposedly due to beam quality issues. At about the same time, KaiDomain offered P60 drop-ins and flashlights with the XT-E. Cree uses the XT-E LED in its line of household light bulbs, introduced in 2013. [http://www.cree.com/products/pdf/XLampXT-E.pdf Datasheet], [http://www.cree.com/news-and-events/cree-news/press-releases/2012/february/120207-xte press release].
Cree is a LED manufacturing company based in Durham, North Carolina. They produce a number of different models of high output LEDs that are widely used in flashlights. They do not actually make flashlights, though some companies will describe their product as a "Cree flashlight." This refers to the LED inside the flashlight.
Cree bins individual models of LED on the basis of total flux or light output, typically measured at 350mA. Bin numbers might be P4, Q2, Q3, Q4, Q5, R2, R3, R4, and R5 with each bin being about 5% additional flux. The P4 is 80 lumens, a Q5 would be 107 lumens, and the R5 bins are 137 lumens. At higher amperage than 350mA, the brightness goes way up, with the XP-G producing 3 times as many lumens at a maximum current of 1500mA.
Cree classifies tints of white LEDs as being warm, neutral, and cool, but has recently added "outdoor white" in between and overlapping neutral and cool (4000-5300K). Tints are binned using a system based on the ANSI White standard. Cree's tints subdivide and expand on the ANSI regions giving bins such as cool 1B, neutral 5B1, and warm 7D2, though many other tints and subdivisions are available. Click on the graphic at right to see all of the bins, though not all bins are available.
In addition, Cree produces High CRI LEDs, with CRI values of 80, 85, and 90 represented by bins H1, P1, and U1 respectively (separately, L1 represents normal CRI white LEDs, and O1 is outdoor white).
Below are output numbers for different currents for the various brightness bins of more current LED models (see Old Cree LEDs for past models). There is more information available with the Cree Product Characterization Tool, an online calculator that allows you to look up output based on more factors. The numbers on this page, like those given by the PCT, are based on charts in the LED datasheets.
Large die high power LED has versions that run at 6, 9, or 36 volts with maximum power of 18 watts, first available around November 2012. The LED is 8.9mm x 8.9mm and the light will be floody compared to the smaller XM-L. The first production lights to use this LED were the Crelant 7G10 and Solarforce S200, introduced in May 2013. The LED is binned at 85°C. The bins shown below have been increased by 15% to give output at 25°C for easier comparison to other LEDs.
Brightness Bins for 6-volt Cree MT-G2 at 25° C
Bin
1100mA 100%
1500mA 172%
3000mA 230%
D0
460-506
598-658
1058-1164
E0
506-552
658-718
1164-1270
F0
552-598
718-777
1270-1375
G0
598-644
777-837
1375-1481
H0
644-690
837-897
1481-1587
J0
690-736
897-957
1587-1693
K0
736-782
957-1017
1693-1799
M0
782-828
1017-1076
1799-1904
N0
828-874
1076-1136
1904-2010
P0*
874-920
1136-1196
2010-2116
XM-L2
Same 5mm x 5mm size as the original XM-L but with up to 20% more output. Introduced in December 2012. Like the XP-G2, the XM-L2 is silver on top, has two bonding wires, and the die has dots instead of lines. The XM-L2 is significantly larger than the XP-G2 and has a round hole at the upper left as opposed to the XP-G2's square hole. The LEDs are binned at 85°C, so the values shown below have been increased by 13.7% to make comparisons with other LEDs binned at 25°C easier. The first production lights to feature the XM-L2 were the ThruNite Catapult V3 and TN31 in January 2013, followed by a number of Xeno lights which also had options for neutral tints in Feburary. Press release.
Cree XM-L2 is the same size as the original XM-L, but a new design
Brightness Bins for Cree XM-L2 at 25°C (max is U3 bin)
Bin
700mA 100%
1000mA 138%
1500mA 194%
3000mA 328%
S4
186-196
256-268
360-377
612-641
S5
196-207
268-284
377-400
641-679
S6
207-227
284-313
400-439
679-746
T2
227-250
313-343
439-483
746-820
T3
250-273
343-375
483-528
820-895
T4
273-296
375-406
528-571
895-970
T5
296-318
406-438
571-615
970-1044
T6
318-341
438-468
615-659
1044-1119
U2
341-364
468-500
659-703
1119-1193
U3*
364-386
500-533
703-750
1193-1268
XP-E2
Introduced in September 2012, this redesign is similar to the XP-G2. Cree claims up to 20% more output than the original XP-E at half the cost in terms of lumens per dollar. Press realease, datasheet. The XP-E2 is binned at 85°C, but for ease of comparison, the output numbers below are increased by 16% to get 25° values.
Brightness Bins for Cree XP-E2 at 25°C (max bin is R3)
Bin
350mA 100%
700mA 171%
1000mA 218%
P2
78.0-85.7
133-147
171-187
P3
85.7-93.5
147-160
187-204
P4
93.5-101
160-174
204-222
Q2
101-109
174-187
222-238
Q3
109-116
187-198
238-253
Q4
116-124
198-212
253-270
Q5
124-132
212-226
270-289
R2
132-142
226-242
289-309
R3*
142-151
242-258
309-329
XP-G2
Introduced in July 2012, the XP-G2 is an all new design with the same size as the earlier XP-G. Like Cree's other 2012 offerings, the XP-G2 is binned at 85°C, but for ease of comparison, output shown on this page is increased by 13% to get 25° values. In August 2012, Foursevens was the first company to adopt this LED, claiming up to 20% more output and a 5% smaller hotspot for greater throw compared to the same models using a XP-G. Press release, Datasheet
Cree XP-G2 LED is the same size as the XP-G, but a different design
Brightness Bins for Cree XP-G2 at 25°C (max is S4 bin)
Bin
350mA 100%
700mA 183%
1000mA 243%
1500mA 329%
Q4
113-121
206-220
275-294
373-399
Q5
121-129
220-235
294-313
399-425
R2
129-138
235-252
313-336
425-454
R3
138-147
252-268
336-357
454-485
R4
147-157
268-287
357-382
485-518
R5
157-168
287-308
382-409
518-554
S2
168-177
308-324
409-431
554-584
S3
177-186
324-341
431-453
584-614
S4*
186-195
341-358
453-475
614-644
XP-L
Introduced in May 2014, the XP-L puts the same size die as the XM-L2 onto the smaller 3.5mm board of the XP-G (shaving off the edges of the dome to make it fit). Due to the larger die, it will not throw quite as well as the smaller die of the XP-G, but it puts out more light and can be driven at higher currents. Binned at a higher current than the XM-L2, higher bins are typical for the XP-L, but a V5 bin XP-L is roughly equivalent in output to a U2 bin XM-L2. In June 2015, Cree began shipping a "high intensity" version of the LED with a flat coating instead of a dome that could offer the throw of a de-domed LED without the trouble. The original domed version is referred to as "high density."
Cree XP-L LED puts a large die in a XP-G size package under a frosted dome
Brightness Bins for Cree XP-L at 25°C (max is V6 bin)
