Luminus is a LED manufacturer based in Billerica, Massachusetts. They produce the SST-50 and SST-90 LED's (SSR-50 and SSR-90 are just the LED mounted to a star). These LED's compete with the SSC P7 and Cree MC-E, but the LED is a single emitter instead of 4 separate ones working together. The size of the emitter is similar so there is a large hotspot, but because the entire emitter lights up, SST-50 lights are less prone to a donut hole of darkness at the center of the beam.

Luminus SST-90 LED

SST-50

The SST-50 is 2.2mm x 2.2mm (5 mm²) drawing up to 5 amps while outputting up to 1250 emitter lumens. This is a big current draw for a flashlight and batteries and produces a large amount of heat, therefore the LED's are driven lower than maximum. Flashlights using this LED are capable of 500 lumens of output on one 18650 li-ion cell and up to 900 lumens using 2 18650's. web page datasheet

The SST-50 is used in the ThruNite Catapult, LumaPower D-Mini VX Ultra, Olight M21 Warrior Luminus, and the Tiablo AS50.

Here are the Brightness Bins for the SST-50. Note that unlike Cree, Luminus gives benchmarks at some current per mm² instead of just a current level to the LED. Bins were revised in February 2011. Here are the Old Luminus bins.

Luminus SST-50 (maximum bin is J)
Bin 1750mA
(350mA/mm²)
100%
2800mA
(560mA/mm²)
160%
5000mA
(1000mA/mm²)
270%
WF 275-350 440-560 743-945
WG 350-425 560-680 945-1148
WH 425-500 680-800 1148-1350
WJ* 500-600 800-960 1350-1620
WK 600-700 960-1120 1620-1890


SST-90

The SST-90 is 3mm x 3mm (9mm²) drawing up to 9 amps while outputting up to 2250 emitter lumens. web page datasheet


Luminus SST-90 (maxium bin is N)
Bin 3200mA
(350mA/mm²)
100%
5000mA
(555mA/mm²)
155%
9000mA
(1000mA/mm²)
270%
WK 600-700 930-1085 1620-1890
WL 700-850 1085-1318 1890-2295
WM 850-1000 1318-1550 2295-2700
WN* 1000-1200 1550-1860 2700-3240
WP 1200-1450 1860-2248 3240-3915

CBM-360

The CBM/CSM-360 is four SST-90 dies mounted on a single device. It is designed as a replacement for high power illumination lamps. web page

Tint Bins

 
Luminus tint bins plotted on chromaticity chart

Luminus uses tint bins based on ANSI White groupings, but they are expanded and subdivided. Each ANSI quadrangle is subdivided into four quadrants plus there are additional regions outside of ANSI. In product numbers, the tint bin is given towards the end, just before the last 3 digits which indicate a wavelength. Other parts of the product number give the ANSI CCT value:

Luminus Color Temperature Codes
Bin Name Temperature
DL Daylight 6500-5000K
CL Cool white 5000-4000K
WT White 4500-3500K
WR Warm white 3500-2700K

Luminus also assigns a CRI code where S is a CRI of 70, M is 83, and H is 92.

See Luminus' Phlatlight Binning and Labeling guide for more information.


http://www.luminus.com/