All public logs

Combined display of all available logs of Flashlight Wiki. You can narrow down the view by selecting a log type, the username (case-sensitive), or the affected page (also case-sensitive).

• 09:39, 9 April 2016 Brted talk contribs uploaded a new version of File:Cree XP-E2.jpg (a little brighter)
• 18:24, 6 April 2016 Brted talk contribs uploaded File:Cree XP-E2.jpg (Cree XP-E2 LED)
• 18:59, 8 March 2016 Brted talk contribs uploaded a new version of File:Cree-xpl-hi.jpg
• 16:23, 8 March 2016 Brted talk contribs uploaded File:Cree-xpl-hi.jpg (Cree XP-L HI has no dome, allowing greater throw)
• 20:06, 6 March 2016 Brted talk contribs uploaded a new version of File:Nichia219c.jpg (rotated to put cathode at lower left like other pictures)
• 13:30, 5 March 2016 Brted talk contribs uploaded File:Nichia219c.jpg (Nichia 219c LED. Photo courtesy of BLF member djozz, used with permission.)
• 07:24, 25 February 2016 Brted talk contribs uploaded File:A17l-fet+1.jpg (A17L FET + 1 driver developed by Wight and used in the BLF A6. The microprocessor on the left controls the FET (on the right) and the 7135 (bottom) provides regulation for Low and Medium modes.)
• 12:00, 7 February 2016 Brted talk contribs uploaded a new version of File:Xp-l.jpg
• 12:25, 30 January 2016 Brted talk contribs uploaded File:Xp-l.jpg (Cree XP-L LED in a BLF special edition Manker A6)
• 20:42, 6 December 2015 Brted talk contribs uploaded File:Flashlight-parts.jpg (Exploded view of Supfire A6-T6 by BLF member djozz, annotated by BLF member KGB. Used with permission.)
• 13:09, 28 February 2015 Brted talk contribs uploaded File:Digichargerd4.jpg (Nitecore Digicharger D4 can charge 4 batteries of different sizes and chemistries including NiMH, Li-ion, IMR, and LiFePo4 and has a digital readout for voltage, current, time, and charging status.)
• 12:36, 1 February 2015 Brted talk contribs uploaded File:Nichia219b.jpg (Nichia 219b LED)
• 14:14, 4 May 2014 Brted talk contribs uploaded File:Sunwaymand40a.jpg (Sunwayman D40A)
• 16:32, 29 September 2013 Brted talk contribs uploaded File:Ultrafire-c8.jpg (UltraFire C8 is an 18650 light with a larger diameter head for greater throw.)
• 13:06, 4 July 2013 Brted talk contribs deleted page File:Cree xr-e.jpg (Deleted old revision 20130704180600!Cree_xr-e.jpg: not needed)
• 13:06, 4 July 2013 Brted talk contribs uploaded a new version of File:Cree xr-e.jpg (Not worried about hotlinking anymore)
• 13:05, 4 July 2013 Brted talk contribs deleted page File:Ansiwhite.jpg (Deleted old revision 20130704180421!Ansiwhite.jpg: not needed)
• 13:04, 4 July 2013 Brted talk contribs uploaded a new version of File:Ansiwhite.jpg (Not worried about hotlinking anymore)
• 17:12, 29 June 2013 Brted talk contribs uploaded File:Ansi-white.jpg (Chromaticity chart with divisions used by Cree and Philips Lumiled with some subdivisions used only by Cree. This chart was generated by CPF user DFiorentino and is used at Flashlight Wiki by permission.)
• 17:10, 29 June 2013 Brted talk contribs uploaded a new version of File:Ansiwhite.jpg (trying to stop hotlinking)
• 12:54, 29 June 2013 Brted talk contribs uploaded File:Cree xre.jpg (Cree XR-E LED (from a Uniquefire S10). The brown outline around the die indicates this XR-E uses the smaller EZ900 die)
• 12:53, 29 June 2013 Brted talk contribs uploaded a new version of File:Cree xr-e.jpg (Changing this image to try to prevent hotlinking.)
• 13:48, 6 April 2013 Brted talk contribs uploaded File:Tail.jpg (End of flashlight with tail removed. To bypass the switch, use a wire or paper clip to connect the negative end of the battery to the bare metal threads on the tube. The light should light up. If you have an amp meter, you can measure tailcap current d...)
• 13:46, 6 April 2013 Brted talk contribs uploaded File:Tailcap.jpg (Flashlight tailcap showing spring and retaining ring with dimples. Use needlenose pliers in the dimples to tighten the ring. This tailcap is from an Ultrafire WF-502B.)
• 16:04, 14 March 2013 Brted talk contribs uploaded a new version of File:Cree-xte.jpg (rotate image 90 degrees to match other LED's on page)
• 15:06, 1 March 2013 Brted talk contribs uploaded File:Coatedlens.jpg (The glass lens with anti-reflective coating on the right shows an obvious decrease in the amount of light reflected onto the wall vs. the uncoated plastic lens in the center and the uncoated glass lens on the left. Because of the sharp angle of light o...)
• 12:10, 3 February 2013 Brted talk contribs uploaded a new version of File:Cree-xml.jpg (Updated picture isn't as dark. The LED shown is a neutral XM-L from Illumination Supply)
• 12:08, 3 February 2013 Brted talk contribs uploaded File:Creexm-l2.jpg (The Cree XM-L2 LED is the same size as the original XM-L, but it is a new design. The top is silver, the strips are gone, and there are only 2 bonding wires instead of 3. The LED shown is a T6 flux bin with 3C tint bin from International Outdoor.)
• 21:47, 15 October 2012 Brted talk contribs uploaded File:Luxeonc.jpg (Luxeon C LED, from a Maglite Solitaire LED flashlight)
• 18:37, 3 October 2012 Brted talk contribs uploaded File:Creexb-d.jpg (Cree XB-D LED is similar to the XT-E, but smaller.)
• 19:05, 4 September 2012 Brted talk contribs uploaded File:Xpg2.jpg (Cree XP-G2 LED)
• 09:30, 7 June 2012 Brted talk contribs uploaded File:Samsung3535.jpg (Samsung 3535 LED from a Ultrafire P60 drop-in sold by Manafont.)
• 21:24, 29 May 2012 Brted talk contribs uploaded File:Osram-oslon.jpg (Osram Oslon Square LED)
• 18:31, 27 May 2012 Brted talk contribs uploaded File:Cree-xpc.jpg (Cree XP-C LED installed under the reflector of a Streamlight Microstream.)
• 18:37, 14 May 2012 Brted talk contribs uploaded File:Cree-xte.jpg (Cree XT-E LED. Recognizable by the yellow phosphor coating and the X on the raised die.)
• 18:59, 10 May 2012 Brted talk contribs uploaded File:Nichia219.jpg (Nichia 219 LED has the same footprint as a Cree XP-G)
• 16:34, 25 February 2012 Brted talk contribs uploaded File:Fenix-l2d-p2d.jpg (Fenix L2D and P2D Premium Q5 with Cree XR-E Q5 LED, olive colored)
• 16:29, 25 February 2012 Brted talk contribs uploaded File:Sunwayman-v10a.jpg (Sunwayman V10A with Cree XP-G R5)
• 09:28, 18 February 2012 Brted talk contribs uploaded File:Baked-anodized-lights.jpg (Three lights that were originally black, after being broiled in an oven at 500 degrees F for 30 minutes. The resulting color varies from one manufacturer to another, with the biggest tint shifts available from Type II anodizing, which is more common on bu)
• 17:23, 11 February 2012 Brted talk contribs uploaded File:Mobile-menu.png (Screenshot of the mobile version of the Flashlight Wiki showing the drop down menu. Taken on a iPod Touch 4G.)
• 17:22, 11 February 2012 Brted talk contribs uploaded File:Mobile-home.png (Screenshot of the mobile version of the Flashlight Wiki home page, taken on an iPod Touch 4G.)
• 20:24, 30 November 2011 Brted talk contribs uploaded File:Ledtints.jpg (From left to right (white balance set to 5,200K): Quark MiNi AA (cool white XP-G R5), Olight T20-M (XR-E Q5), Quark 123² Turbo (XP-G S2), 4Sevens Preon 2 (neutral XP-G R4), Quark RGB (neutral white MC-E), SureFire 6P (incandescent), 4Sevens Preon 2 ()
• 14:28, 15 May 2011 Brted talk contribs uploaded File:P60-disk.jpg (Isolation disk placed over the top of the driver. This prevents the aluminum reflector causing a short between the positive and negative parts of the LED. This is a 18mm disk, but it is better to get a 16mm disk which fits inside the outer rim of the pill)
• 09:28, 15 May 2011 Brted talk contribs uploaded a new version of File:P60-driverdry.jpg (square picture)
• 09:19, 15 May 2011 Brted talk contribs uploaded File:P60-ledwired.jpg (The LED with leads from the driver soldered in place. Make sure the solder points don't stick up too high or they could interfere with the reflector.)
• 09:09, 15 May 2011 Brted talk contribs uploaded File:P60-positive.jpg (The bottom of the driver board with the small spring for contact with the positive end of the battery and solder bridges from the driver board to the pill.)
• 22:14, 14 May 2011 Brted talk contribs uploaded File:P60-leads.jpg (Red and black leads are soldered to the driver board. It helps to hold the work in a vise (this is a PanaVise). A magnifying lens helps too (this is called a third hand).)
• 21:47, 14 May 2011 Brted talk contribs uploaded File:P60-driverdry.jpg (The driver fits into the bottom of the pill. After the nubs have been filed down, file down one edge to be flat so that the driver can be pried out easier.)
• 21:45, 14 May 2011 Brted talk contribs uploaded File:P60-center.jpg (Once the LED is in place, you can check whether it is centered by screwing the reflector over it. Before the adhesive sets up, you make adjustments to get the LED perfectly centered.)
• 21:40, 14 May 2011 Brted talk contribs uploaded File:P60-ledmounted.jpg (The LED is glued to the top of the brass pill with thermal adhesive. The key is to get the LED centered and not to cover the holes where the leads from the driver will come up to attach to the LED later.)