All public logs

Combined display of all available logs of Flashlight Wiki. You can narrow down the view by selecting a log type, the username (case-sensitive), or the affected page (also case-sensitive).

• 13:54, 29 June 2013 Brted talk contribs uploaded File:Cree xre.jpg (Cree XR-E LED (from a Uniquefire S10). The brown outline around the die indicates this XR-E uses the smaller EZ900 die)
• 13:53, 29 June 2013 Brted talk contribs uploaded a new version of File:Cree xr-e.jpg (Changing this image to try to prevent hotlinking.)
• 14:48, 6 April 2013 Brted talk contribs uploaded File:Tail.jpg (End of flashlight with tail removed. To bypass the switch, use a wire or paper clip to connect the negative end of the battery to the bare metal threads on the tube. The light should light up. If you have an amp meter, you can measure tailcap current d...)
• 14:46, 6 April 2013 Brted talk contribs uploaded File:Tailcap.jpg (Flashlight tailcap showing spring and retaining ring with dimples. Use needlenose pliers in the dimples to tighten the ring. This tailcap is from an Ultrafire WF-502B.)
• 17:04, 14 March 2013 Brted talk contribs uploaded a new version of File:Cree-xte.jpg (rotate image 90 degrees to match other LED's on page)
• 16:06, 1 March 2013 Brted talk contribs uploaded File:Coatedlens.jpg (The glass lens with anti-reflective coating on the right shows an obvious decrease in the amount of light reflected onto the wall vs. the uncoated plastic lens in the center and the uncoated glass lens on the left. Because of the sharp angle of light o...)
• 13:10, 3 February 2013 Brted talk contribs uploaded a new version of File:Cree-xml.jpg (Updated picture isn't as dark. The LED shown is a neutral XM-L from Illumination Supply)
• 13:08, 3 February 2013 Brted talk contribs uploaded File:Creexm-l2.jpg (The Cree XM-L2 LED is the same size as the original XM-L, but it is a new design. The top is silver, the strips are gone, and there are only 2 bonding wires instead of 3. The LED shown is a T6 flux bin with 3C tint bin from International Outdoor.)
• 22:47, 15 October 2012 Brted talk contribs uploaded File:Luxeonc.jpg (Luxeon C LED, from a Maglite Solitaire LED flashlight)
• 19:37, 3 October 2012 Brted talk contribs uploaded File:Creexb-d.jpg (Cree XB-D LED is similar to the XT-E, but smaller.)
• 20:05, 4 September 2012 Brted talk contribs uploaded File:Xpg2.jpg (Cree XP-G2 LED)
• 10:30, 7 June 2012 Brted talk contribs uploaded File:Samsung3535.jpg (Samsung 3535 LED from a Ultrafire P60 drop-in sold by Manafont.)
• 22:24, 29 May 2012 Brted talk contribs uploaded File:Osram-oslon.jpg (Osram Oslon Square LED)
• 19:31, 27 May 2012 Brted talk contribs uploaded File:Cree-xpc.jpg (Cree XP-C LED installed under the reflector of a Streamlight Microstream.)
• 19:37, 14 May 2012 Brted talk contribs uploaded File:Cree-xte.jpg (Cree XT-E LED. Recognizable by the yellow phosphor coating and the X on the raised die.)
• 19:59, 10 May 2012 Brted talk contribs uploaded File:Nichia219.jpg (Nichia 219 LED has the same footprint as a Cree XP-G)
• 17:34, 25 February 2012 Brted talk contribs uploaded File:Fenix-l2d-p2d.jpg (Fenix L2D and P2D Premium Q5 with Cree XR-E Q5 LED, olive colored)
• 17:29, 25 February 2012 Brted talk contribs uploaded File:Sunwayman-v10a.jpg (Sunwayman V10A with Cree XP-G R5)
• 10:28, 18 February 2012 Brted talk contribs uploaded File:Baked-anodized-lights.jpg (Three lights that were originally black, after being broiled in an oven at 500 degrees F for 30 minutes. The resulting color varies from one manufacturer to another, with the biggest tint shifts available from Type II anodizing, which is more common on bu)
• 18:23, 11 February 2012 Brted talk contribs uploaded File:Mobile-menu.png (Screenshot of the mobile version of the Flashlight Wiki showing the drop down menu. Taken on a iPod Touch 4G.)
• 18:22, 11 February 2012 Brted talk contribs uploaded File:Mobile-home.png (Screenshot of the mobile version of the Flashlight Wiki home page, taken on an iPod Touch 4G.)
• 21:24, 30 November 2011 Brted talk contribs uploaded File:Ledtints.jpg (From left to right (white balance set to 5,200K): Quark MiNi AA (cool white XP-G R5), Olight T20-M (XR-E Q5), Quark 123² Turbo (XP-G S2), 4Sevens Preon 2 (neutral XP-G R4), Quark RGB (neutral white MC-E), SureFire 6P (incandescent), 4Sevens Preon 2 ()
• 15:28, 15 May 2011 Brted talk contribs uploaded File:P60-disk.jpg (Isolation disk placed over the top of the driver. This prevents the aluminum reflector causing a short between the positive and negative parts of the LED. This is a 18mm disk, but it is better to get a 16mm disk which fits inside the outer rim of the pill)
• 10:28, 15 May 2011 Brted talk contribs uploaded a new version of File:P60-driverdry.jpg (square picture)
• 10:19, 15 May 2011 Brted talk contribs uploaded File:P60-ledwired.jpg (The LED with leads from the driver soldered in place. Make sure the solder points don't stick up too high or they could interfere with the reflector.)
• 10:09, 15 May 2011 Brted talk contribs uploaded File:P60-positive.jpg (The bottom of the driver board with the small spring for contact with the positive end of the battery and solder bridges from the driver board to the pill.)
• 23:14, 14 May 2011 Brted talk contribs uploaded File:P60-leads.jpg (Red and black leads are soldered to the driver board. It helps to hold the work in a vise (this is a PanaVise). A magnifying lens helps too (this is called a third hand).)
• 22:47, 14 May 2011 Brted talk contribs uploaded File:P60-driverdry.jpg (The driver fits into the bottom of the pill. After the nubs have been filed down, file down one edge to be flat so that the driver can be pried out easier.)
• 22:45, 14 May 2011 Brted talk contribs uploaded File:P60-center.jpg (Once the LED is in place, you can check whether it is centered by screwing the reflector over it. Before the adhesive sets up, you make adjustments to get the LED perfectly centered.)
• 22:40, 14 May 2011 Brted talk contribs uploaded File:P60-ledmounted.jpg (The LED is glued to the top of the brass pill with thermal adhesive. The key is to get the LED centered and not to cover the holes where the leads from the driver will come up to attach to the LED later.)
• 22:25, 14 May 2011 Brted talk contribs uploaded File:P60-parts.jpg (Parts to build a P60 drop-in. The only things not shown here are an isolation disk and the lead wires from the driver to the LED.)
• 22:44, 1 May 2011 Brted talk contribs moved page Talk:NEXTORCH to Talk:Nextorch (Don't like all caps)
• 22:44, 1 May 2011 Brted talk contribs moved page NEXTORCH to Nextorch (Don't like all caps)
• 22:28, 17 April 2011 Brted talk contribs uploaded File:Turnigy.jpg (Turnigy Accucell 6 hobby charger)
• 10:03, 9 April 2011 Brted talk contribs uploaded File:Ribbon.jpg (The 8-wire ribbon from the clip must be modified to connect to Pin 9 of the USB ISP programmer. Open up the end of the ribbon and move wire 8 over to the 9th position then reassemble.)
• 10:01, 9 April 2011 Brted talk contribs deleted page File:Ribbbon.jpg
• 09:48, 9 April 2011 Brted talk contribs uploaded File:Usbisp.jpg (USB ISP AVR programming board. This attaches to the computer and the ribbon from the clip attaches to this board.)
• 09:40, 9 April 2011 Brted talk contribs uploaded File:Soic8clip.jpg (An SOIC 8 clip with ribbon cable attached. The individual wires of the ribbon must be re-ordered to attach to the correct pins of the Atmel chip the clip will attach to. The 8-wire ribbon has a 10-wire plug that attaches to the USB ISP programmer.)
• 09:37, 9 April 2011 Brted talk contribs uploaded File:Avrisp.jpg (An SOIC 8 clip attached to an Atmel Tiny13A chip on a flashlight driver board. This is the NANJG AK-47 driver.)
• 09:36, 9 April 2011 Brted talk contribs uploaded File:Ribbbon.jpg (An 8-wire ribbon modified to use the 9th wire position in a 10-wire holder. The 8th wire is just moved over one slot.)
• 18:03, 8 April 2011 Brted talk contribs uploaded File:Ak47pins.jpg (Picture of NANJG AK-47 driver with ATMEL ATTiny13 pin numbers labelled.)
• 22:56, 6 March 2011 Brted talk contribs uploaded File:Tir-optic.jpg (Total internal reflection optic. This lens is made of plastic and came with the Mr.Lite BLF-Y4E, which has a Cree XR-E Q5 LED.)
• 23:39, 26 February 2011 Brted talk contribs uploaded File:Sony-bcg34hld.jpg (Sony BCG-34HLD charger with Sony Cycle Energy 1000mA LSD battery)
• 16:12, 23 January 2011 Brted talk contribs uploaded File:Maglites.jpg (Mini Maglites 2xAA and 2xAAA in pewter)
• 10:21, 18 January 2011 Brted talk contribs uploaded File:Sscp4.jpg (Seoul Semiconductor P4 LED, U bin. Photo by Peter Cheuk, used with permission.)
• 10:19, 18 January 2011 Brted talk contribs uploaded File:Luxeon rebel.jpg (Luxeon Rebel LED in a Maglite. Photo by Peter Cheuk, used with permission.)
• 15:35, 12 January 2011 Brted talk contribs uploaded File:Magleds.jpg (Maglite LED's for 3xD cell lights: on left the newer Cree XP-E with the Rebel on the right. Some Maglites started using the XP-E in late 2010. Photo by Peter Cheuk, used with permission.)
• 00:38, 2 January 2011 Brted talk contribs uploaded File:Eqn-throw.png (Equations for converting throw to candela based on ANSI/NEMA FL-1 standard of 0.25 lux)
• 15:23, 31 December 2010 Brted talk contribs uploaded a new version of File:Ssctints.jpg (Previous version was not for P4 and P7 LED's. This one is.)
• 21:48, 30 December 2010 Brted talk contribs uploaded File:Ssctints.jpg (Seoul Semiconductor's tint bins plotted on a chromaticity chart. This graphic created by CPF user DFiorentino and used by Flashlight Wiki with permission.)